Effect of cutting process on the stress corrosion susceptibility of AISI 304L stainless steel

During manufacturing of a component, cutting, turning, grinding, and milling operations are inevitable and these operations induce surface residual stresses. In this study, it is shown that, depending on the process employed for cutting, residual stresses generated at the cut surfaces can vary widely and they can, in turn, make the cut surfaces of austenitic stainless steel (SS) prone to stress corrosion cracking (SCC). An austenitic SS 304L plate was cut using three different procesess: bandsaw cutting, cutting using the cut-off wheel, and shearing. Surface residual stress measurement using the X-ray diffraction (XRD) technique is carried out close to the cutting edges and on the cross-section. SCC susceptibility studies were carried out as per ASTM G36 in 45% boiling magnesium chloride solution. Optical microscopic examination showed the presence of cracks, and confocal microscopy was used to measure the depth of cracks. The study confirmed that high tensile residual stresses present in the cut surfaces produced by cut-off wheel and shear cutting make the surfaces susceptible to SCC while the surfaces produced by bandsaw cutting are resistant to SCC. Hence, it is shown that there is a definite risk of SCC for product forms of austenitic SS with cut surfaces produced using cutting processes that generate high tensile residual stresses stored for a long period of time in a susceptible environment.     

Hot corrosion studies of a salt-coated Ni-based superalloy under flowing wet air and sulfur vapor ambient

Corrosion of a salt-coated Ni-superalloy has been studied at 900°C under a wet air and sulfur vapor ambient. The corrosion thickness, after an incubation of ~60 hr, linearly increases with the corrosion time t and the onset of surface spallation occurred at t ≈ 60 hr. The corroded layer consists of a corrosion front dominated by Cr₃S₄ scales and linear precipitate structures, an inner corrosion layer dominated by Ni₃S₂ and NiO, and an outer corrosion layer dominated by Al₂O₃ networks surrounding the Ni₃S₂ and/or NiO scale structures. The corrosion mechanism is discussed based on the coexistence of H₂O, sulfur, and oxygen.     

某油田油井采出水腐蚀因素研究

我国油田油井生产中采油井管柱腐蚀现象十分普遍,所以在注CO_2驱进行开采过程中要进行采出水的质量分析。对现阶段的油田生产腐蚀及防腐技术进行论述,提出相对应的防腐措施,进一步为油田生产作业提高产量。     

水射流表面改性对国产Zirlo锆合金包壳管加速腐蚀氧化膜形貌的影响

为进一步提高国产锆合金包壳管性能,提高反应堆安全性,对国产Zirlo锆合金进行水射流冲击强化,研究在高温高压水腐蚀条件下不同冲击压力对样品表面氧化膜的影响,并与未冲击样品进行对比。结果表明,样品表面在不同压力的冲击下耐蚀性差异较大,当冲击压力达到40 MPa时样品表面氧化膜状态较好,相比于未冲击样品氧化膜厚度减少4.3%,在10 MPa和20 MPa冲击下则出现腐蚀加速情况。     

Entwicklung und Validierung eines Kühlmittelsensors zur Bewertung der Korrosionsschutzwirkung

A sophisticated thermal management is one of the main subsystems that enables combustion engines with high power density. In this context the demands on coolants are also increasing. There has to be a certain level of corrosion protection to ensure the functionality of the cooling system. Hereafter the result of an electrochemical sensor development is presented. With the knowledge of analytical and electrochemical results a quick test for characterizing coolants corrosion protection has been developed and validated.     

耐蚀合金中TiN析出机制

摘要：TiN颗粒尺寸及其分布对耐蚀合金性能有明显的影响，因此有必要对TiN在铸坯中的分布及其析出行为进行研究。采用扫描电镜(SEM)、金相显微镜（OM）观察了TiN夹杂物在铸坯中的分布、尺寸及其形貌；基于热力学和动力学理论分析了耐蚀合金铸坯中TiN夹杂物的析出时机及其尺寸，结合试验结果和理论计算明确了TiN夹杂物在凝固后铸坯中的位置和尺寸与析出时机的关系，为控制TiN夹杂物提供理论指导。结果表明，冶炼过程中析出的TiN夹杂物尺寸较大，在凝固过程中被枝晶吞没，位于铸坯枝晶内和等轴晶内；微观偏析计算结果表明，在凝固分数为0.55时，TiN开始析出，最开始析出TiN夹杂物的逐渐长大，长大后的TiN易于被二次枝晶吞没，最终位于铸坯中的枝晶间和等轴晶内，后期析出的TiN则在枝晶间和等轴晶间。固相中析出的TiN夹杂物长大较慢，尺寸细小，最终位于奥氏体晶界。     

华北地区含硫化氢地下储气库脱硫运行技术

为了进一步推动国内含H_2S地下储气库的优化运行,以华北地区X地下储气库为例,为防止其运行过程中采出的天然气因含H_2S引发的安全问题,提出了有针对性的脱硫运行技术对策。主要包括:井筒抗硫技术、含硫气井井口失控远程点火技术和地面H_2S处理技术。地下选用国产宝钢生产的D114.3 mm BGT1气密封型防硫化氢螺纹油管及耐压强度达34.5 MPa的井下安全阀。对含硫井口配备失控远程点火系统。在地面主要采用"活性炭+脱硫剂"分层装填脱硫塔的方式实现采出混合气体脱硫,并结合储气库井受双向压力及井底热传导效应促进硫溶解。通过摸索并实施一系列针对性的技术对策,X储气库完全自主实现零事故安全运行,为类似地下储气库的建设及运行提供了一定的参考。     

Preparation and electrochemical characterization of Ti-based amorphous metallic glass with high strength

Ti-based amorphous metallic glasses have excellent mechanical, physical, and chemical properties, which is an important development direction and research hotspot of metal composite reinforcement. As a stable, simple, efficient, and large-scale preparation technology of metallic powders, the gas atomization process provides an effective way of preparing amorphous metallic glasses. In this study, the controllable fabrication of a Ti-based amorphous powder, with high efficiency, has been realized by using gas atomization. The scanning electron microscope, energy-dispersive spectrometer, and X-ray diffraction are used to analyze surface morphology, element distribution, and phase structure, respectively. A microhardness tester is used to measure the mechanical property. An electrochemical workstation is used to characterize corrosion behavior. The results show that as-prepared microparticles are more uniform and exhibit good amorphous characteristics. The mechanical test shows that the hardness of amorphous powder is significantly increased as compared with that before preparation, which has the prospect of being an important part of engineering reinforced materials. Further electrochemical measurement shows that the corrosion resistance of the as-prepared sample is also significantly improved. This study has laid a solid foundation for expanding applications of Ti-based metallic glasses, especially in heavy-duty and corrosive domains.     

Effect of heat treatment and zircon addition on the properties of low-cement castables based on recycled alumina grog

In this investigation, low-cement castables were prepared using 70% alumina grog aggregates obtained from crushed alumina brick waste. The aggregates were thermally treated at 1550 °C for 3 h. Four types of low-cement castables were prepared with various types of aggregates (alumina grog with or without thermal treatment) and fillers (with or without zircon addition), and they were evaluated in terms of their physical, thermal, and chemical properties. Microstructural analysis via scanning electron microscopy (SEM) was performed on the castables before and after slag attack. Compared to the other fabricated castables, the thermally treated alumina grog castables with zircon showed better physical properties, such as a higher bulk density, cold crushing strength, and modulus of rupture and a lower apparent porosity and water absorption. In addition, they had a higher positive linear thermal expansion, refractoriness under load, permanent linear change, and hot modulus of rupture. The results of the SEM with energy dispersive X-ray analysis of the prepared castables confirmed that the mullite and anorthite phases were predominant when zircon was not added and the zircon–mullite phase additionally appeared upon the incorporation of zircon. A quantitative elemental analysis via X-ray fluorescence spectroscopy was employed to determine the composition of the castables. X-ray diffraction analysis showed that the alumina grog castables had a high mullite and low anorthite content, and the thermally treated alumina grog had a high anorthite, low mullite, and high zircon content. The improvement in the mechanical and thermo-mechanical properties of the castables with thermally treated alumina grog and added zircon can be attributed to the formation of the zircon–mullite phase with a low mullite phase content.